LYNX Touch L7000 Series Security System. Remove the key fob programming from the security system. An alarm occurs, the LYNX Touch internal sounder. View and Download Honeywell Lynx Plus Series installation and setup manual online. Honeywell Lynx Plus Series Security Systems. Lynx Plus Series Security System pdf.

Tip: If your system is currently monitored by an alarm company, you may want to let them make passcode changes for you. Check with your alarm company representative for specific details and help on programming your system. If the alarm isn’t under contract with a company, you may want to program a new passcode yourself. Here’s how to do it! You’ll need to know either the installer code or master code to make programming changes.

If you have no working passcode for the system, skip to “Resetting the installer code”. Ademco Lynx System Code Layout: • The Lynx has a total of eight passcodes, numbered 01-08. Code 01 is designated as the Installer Code, and is used by the alarm company for system set-up. It can also change the Master Code.

• Code 02 is the Master Code, and is used to change both itself and the User Codes 03-08. Gloria Estefan Oye Mi Canto Los Grandes Exitos Rar. • The “8” key is also the “Program” function button, and is used to make passcode changes.

• When making passcode changes, don’t wait too long between keystrokes, or the system will time out. If this happens, start the sequence of key presses over from the beginning. If you already know a passcode for the system, here’s how to figure out which one it is: Enter (4-digit code) + 8 + 00. If the Ademco Lynx wireless displays “20”, you have the installer code. To leave it the same, press *99 to exit programming. To change it, press *20, followed by the desired new installer code.

Press *99 to exit program mode, then skip down to “Changing the Master Code”. If the system doesn’t display “20”, you have either the master code or one of the user codes. Enter (4-digit code) + 8 02 + 1234 + 1234. If the keypad beeps three times, you have the master code, and it’s just been changed to “1234”. This is the factory default, so you’ll want to change it to something more secure. If the unit doesn’t beep, you have a regular user passcode. Skip to “Resetting the Installer Code”.

To use the master code to change itself, follow this format: (old master code) + 8 + 02 + (new master code) + (new master code). Notice that the new passcode must be entered twice for the change to take effect. As an example, to change the master to '9876', you would enter: 1234 + 8 + 02 + 9876 + 9876. After entering the new code the second time, the unit will sound 3 beeps to confirm the change. Resetting the Installer Code 1. Remove the Ademco Lynx system from its base by pressing a flat-bladed screwdriver gently into each slot along the top edge of the unit. Speedtouch St536 Usb Driver Programs. Plug in the low voltage transformer, or re-connect the loose transformer wire carefully.

Within 50 seconds of power-up, press the * and # keys at the same time. The display should show “20”. Press # + 2 + 0.

The display will scroll through the current 4-digit installer code. Jot this down. (Note: The display shows single digits with a leading zero, so 01 = 1, 02 = 2, etc.).

To change the installer code, press *20, followed by a new 4-digit installer code. Exit programming mode by pressing *99. Resetting the Master Code A new master code can be programmed using the installer code, using this format: (Installer Code) + 8 + 02 + (New 4-digit master code). Notice that when using the installer to change a master code, you’re not required to enter the new code a second time. Adding User Codes to the Ademco Lynx System Use the master code to add users with the format: (master code) + 8 + (2-digit user number 03-08) + (new 4-digit user code).